Which three mam functions are provided by OTV to achieve failure isolation? (Choose
three.)
A. unknown Unicast traffic suppression
B. optimal outbound routing
C. Spanning Tree isolation
D. use of multiple OTV overlays
E. ARP optimization
Answer: A,C,E
Friday 18 August 2017
Cisco 400-151 Practice Question 6
A vPC stretched from two leaf switches up to an ASA Firewall. You are configuring
the VPC as an L3OUT interface in an Cisco ACI Fabric. How is the Layer 3
Configuration applied?
A. Each link must be configured as a Layer 2 link.
B. The VPC configuration itself must be seen as a Layer 2 Portchannel stretching over two devices. A subinterface in the port channel configuration of the VPC must be configured ay both the ends on the VPC.
C. A separate SVI must be configured in the ACI fabric and the VLAN of the SVI must be allowed on the VPC trunk configuration.
D. Each endpoint of the VPC must be configured with an IP address in the same range
Answer: C
A. Each link must be configured as a Layer 2 link.
B. The VPC configuration itself must be seen as a Layer 2 Portchannel stretching over two devices. A subinterface in the port channel configuration of the VPC must be configured ay both the ends on the VPC.
C. A separate SVI must be configured in the ACI fabric and the VLAN of the SVI must be allowed on the VPC trunk configuration.
D. Each endpoint of the VPC must be configured with an IP address in the same range
Answer: C
Cisco 400-151 Practice Question 5
Which three statements about ACI border leaf are true? (Choose three.)
A. Any ACI leaf can be a border leaf. There is no limitation in the number of leaf switches that can be used as border leaves.
B. The border leaf can also be used to connect to compute. IP storage, and service appliances.
C. The border leaves are ACl leaves that provide Layer 3 connections to outside networks.
D. The border /eaves are dedicated leaf switches that support on only Layer 2 and Layer 3 out in an ACI fabric.
E. Only 32 border leaves are supported an ACI fabric
Answer: A,B,C
A. Any ACI leaf can be a border leaf. There is no limitation in the number of leaf switches that can be used as border leaves.
B. The border leaf can also be used to connect to compute. IP storage, and service appliances.
C. The border leaves are ACl leaves that provide Layer 3 connections to outside networks.
D. The border /eaves are dedicated leaf switches that support on only Layer 2 and Layer 3 out in an ACI fabric.
E. Only 32 border leaves are supported an ACI fabric
Answer: A,B,C
Cisco 400-151 Practice Question 4
Which two statements about OTV are true?(Choose two)
A. The authoritative edge device is the active forwarder for multicast and unknown unicast for all VLANs.
B. The join interface must be a Layer 2 interface.
C. no special license is required for OTV. D. OTV requires a separate VDC if SVIs for the extended VLANs are to be configured on the same switch.
E. Only one join interface can be specified per overlay. F. OTV runs over a distance victor routing protocol.
Answer: D,E
A. The authoritative edge device is the active forwarder for multicast and unknown unicast for all VLANs.
B. The join interface must be a Layer 2 interface.
C. no special license is required for OTV. D. OTV requires a separate VDC if SVIs for the extended VLANs are to be configured on the same switch.
E. Only one join interface can be specified per overlay. F. OTV runs over a distance victor routing protocol.
Answer: D,E
Cisco 400-151 Practice Question 3
While doing service insertion with vASA with route peering, which two parts must be
configured? (Choose two.)
A. The path for interfaces must be specified when the L4-L7 device is created.
B. The route peering profile must be specified when the L4-L7 Service Graph template is created.
C. The VM name must be specified when the L4-L7 device is created.
D. The chassis must be specified when the L4-L7 device is created.
Answer: A,B
A. The path for interfaces must be specified when the L4-L7 device is created.
B. The route peering profile must be specified when the L4-L7 Service Graph template is created.
C. The VM name must be specified when the L4-L7 device is created.
D. The chassis must be specified when the L4-L7 device is created.
Answer: A,B
Cisco 400-151 Practice Question 2
Which Ether type is used to identify FIP?
A. 0x8914
B. 0x8906
C. 0x8915
D. 0x8905
Answer: A
Explanation: Ref:http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/fcoe/513_n1_ 1/b_Cisco_n5k_fcoe_config_gd_re_513_n1_1/b_Cisco_n5k_fcoe_config_gd_re_513_n1_1 _chapter_010.html
A. 0x8914
B. 0x8906
C. 0x8915
D. 0x8905
Answer: A
Explanation: Ref:http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5000/sw/fcoe/513_n1_ 1/b_Cisco_n5k_fcoe_config_gd_re_513_n1_1/b_Cisco_n5k_fcoe_config_gd_re_513_n1_1 _chapter_010.html
Cisco 400-151 Practice Question 1
Which Cisco UCS Director feature enables you to view the REST API URL for every report
displayed in Cisco UCS Director?
A. report metadata
B. orchestration feature set
C. REST API Browser
D. automation feature set
Answer: A
displayed in Cisco UCS Director?
A. report metadata
B. orchestration feature set
C. REST API Browser
D. automation feature set
Answer: A
Subscribe to:
Posts (Atom)